|
Best tool I've added in 45 years, & the rules take your projects to a whole new level of accuracy.
In no time at all you will be making perfect box joints, dovetails and other more exotic joints. This is an excellent piece of equipment. Take the time to set it up properly and be accurate with your initial set up measurements on the table (unless you have the INCRA table ready laid out) Perfect repeatability and super accurate results. Furthermore, INCRA are an excellent company, with superb customer services and personal feedback. I have a bunch of INCRA stuff and it is all absolutely first rate.
I do beleive that through dovetails on a tradition machine my be a little easier (you don't have to cute off any rounded areas, etc). I've finally started using this system after determining whether I wanted to buy a longer router table, or just modify my current one (the latter won out). However, you can't do many of the things possible with this system either. Incra was produce a well built and accurate system. Repeatability is where this system really shines. The learning curve is relative steep, I believe. But once you've got a handle on it, there is nothing like it.
Cutting box joints for small boxes has always been a little hazardous on the table saw, but this jig makes it safe and extremely accurate. The router cut out overhangs the bench. Ive had this Incra system for a couple years now. You want to really pay attention to the instructions when constructing your "table" as some of the measurments are pretty critical. I am very pleased with this Incra jig and will continue to explore its many uses. Small, accurate dovetail joints are easily accomplished and repeatable if you keep a good log of settings. I had to build mine on a piece of mdf that I can remove from the workbench, as it is also my table saw outfeed table.
Just unbolt the board and pick the whole thing up and stash it in the back room. I am still discovering new ways to use it. Little cumbersome, but works well and saves time by not having to tear down the incra each time. There is a bit of a learning curve, the video really helps (wish mine was dvd), and the book is pretty good. Not overly difficult, just have to pay attention. This unit is very well designed and constucted of top notch materials. Highly recommend.
With the exception of making curves and following router templates, this tool will let your router do just about any cut you can think of in an X Y plain. It's all based on a lead screw with a pitch of 1/32". All that is needed is a router lift to get that Z axis, which I don't have, and it hasn't slowed me down too much.Incra has done an excellent job of every aspect of the LS Super System. In addition it has a hi-rise fence for running boards on edge.
American tool design and manufacturing at it's finest. This is the most thought out and best designed tool I have ever used. I even measured the repeatbility to 1/2000 of an inch. I can set mine up in about 20 minutes.
Also, useful to just knock a fraction of an inch from the edge of a workpiece (like mitres). This enables the fence snap at any 1/32 increment along the 17 inch reach, and it is always repeatable. Need to get between 1/32, no problem, it has a vernier dial that basically moves the fence in 1/1000 increments. This allows very exact placement of the cutter tool relative to the work piece. What to say.
You will need a larger router table for this to work. Mine is 48x38'This unit comes with a second fence that attaches to the main one to allow clearence of larger bits (a must have), in addition, you can offset this second fence and with the use of a strait cutter bit you now have a jointer. It has a stop block which is genius. Lets you place the stop anywhere along either fence and it too will snap 1/32" increments, plus you can still get between the stops with a vernier screw.This kit comes with a sliding fence most useful for dovetails or edge cuts. The fence once installed is rock solid, and can quickly be removed from the router table, broken down and put away. It's genius how it works. I also like the vacuum attachment for dust collection.
It makes woodworking like machining with an upside down mill. This is a great feature for those of us that work in the car garage. The kit includes template ruler guides and a very simple to follow guide for making interlocking joints like box and dovetails. It even looks cool.
|
